Detcon SmartWireless RXT-300 Manual de instrucciones Pagina 10
- Pagina / 47
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RXT-300 SmartWireless™
RXT-300 Wireless IM Rev. 2.0 Page 4 of 41
1.3 Model 100 Terminal Board (Optional)
The RXT-300 wireless transceiver can be ordered with an optional Model 100 Terminal Board mounted in a
condulet/J-Box (See
Figure 4). The terminal board includes connector plugs for the following:
J1: 6-Pin Phoenix Connector RXT-300 Wireless Transceiver
J2: 5-Pin Phoenix Connector Slave Device/HMI/Master Controller
J3: 6-Pin Connector RXT-300 Programming Port (Detcon Factory use only)
J4: 3-Pin Phoenix Connector Model 100 Loop Powered LED display
J5: 3-Pin Phoenix Connector 7-30VDC External power source or 24VDC Solar Panel
J6: 8-Pin Beau Connector 12VDC Battery Power (Use only Detcon’s Smart Battery Pack)
J7: 3-Pin Phoenix Connector Spare Modbus™ Connection
J8: 3-Pin Phoenix Connector RXT Programming Interface to Wireless Transceiver
Figure 4 Model 100 Terminal Board
1.4 Smart Battery Pack (Optional)
The RXT-300 transceiver can also be powered by an optional battery pack that enables it to be remotely
mounted without the need for any cables because of its wireless operation. The available battery pack is
Detcon’s plug-in Smart Battery Pack which provides an output of 12VDC (See
Figure 5). If installed, the
RXT-300 transceiver will detect the battery and will continuously query the battery pack for remaining battery
life. The battery pack consists of rechargeable Lithium-Ion batteries and is equipped with integrated safety
electronics that include fuel gauge, voltage, current and temperature monitoring circuits. This “smart”
circuitry continuously monitors the battery’s condition and reports critical status information to the wireless
transceiver via the Modbus™ registers. The battery pack is designed to plug onto an 8-pin Beau connector on
the Model 100 Terminal Board and should not be exposed to outside elements without being housed and
protected. Only Detcon products specifically designed to utilize these battery packs should be used.
Operating periods before recharge will vary based on devices attached along with the transceiver and the usage
of those devices, but can be as long as 2-3 months and battery life can be up to 5 years before battery pack
replacement is required. Improper use of the battery pack may be hazardous to personnel or the environment
and will void the warranty.
- Model RXT-300 1
- Page intentionally blank 2
- Table of Contents 3
- Table of Figures 4
- List of Tables 5
- 1.0 Introduction 7
- 1.2 RXT-300 Wireless Radio 9
- RXT-300 SmartWireless™ 10
- Figure 5 Smart Battery Pack 11
- 1.6 Solar Panel (Optional) 12
- 2.0 Installation 13
- 2.2 Mounting 14
- 2.2.1 Remote Mounting 15
- 2.3.2 Modbus™ A & B 19
- 2.3.3 Alarm 1-4 19
- 2.3.4 4-20mA A & B 20
- 3.0 System Operation 21
- 3.1 Station Configuration 22
- 3.2 HMI Station Operation 22
- 3.4 Alarm Station Operation 23
- 3.4.2 Alarm Zones 24
- 3.5 Network Sleep 25
- 3.6 Network Control 25
- 3.6.2 Alarm Inhibit 26
- 3.6.3 Alarm Test 26
- 3.6.4 RF Silence 26
- 4.0 System Configuration 27
- 4.2.2 Alarm Zone Build Info 28
- 4.2.3 RXT-300 Build Info 29
- 4.3.1 Network Parameters 30
- 4.3.2 Zones 31
- 4.4.1 RXT-300 Main Settings 31
- 5.0 Modbus Operation 33
- 5.1.1 Address Translation 34
- 5.2.1 Modbus™ Exceptions 35
- Table 5 RXT-300 Register Map 36
- 5.3.8 Register – Control 38
- 5.3.9 Register – Status 38
- 5.3.10 Register – Timestamp 38
- 6.0 Troubleshooting Guide 39
- 7.0 Warranty 39
- 8.0 Specifications 40
- 8.1 Spare Parts 41
- 8.2 Revision Log 42
- Jumper Settings 43
- Jumper Setting 47
Polar CS200 manuali
Manuali dei proprietari e guide per l'utente per Monitor di ritmo cardiaco Polar CS200.
We fornisce 1 manuali pdf Polar CS200 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentarios a estos manuales