Detcon 700 Remote Sensor/Alarm Relay Module Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Detcon 700 Remote Sensor/Alarm Relay Module. Detcon 700 Remote Sensor/Alarm Relay Module User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 17
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Model 700
Remote Sensor/Alarm Relay Module
Operator’s Installation and Instruction Manual
DETCON, Inc.
3200 Research Forest Dr.,
The Woodlands, Texas 77387
Ph.281.367.4100 / Fax 281.298.2868
www.detcon.com
March 16, 2011• Document #3220• Revision 1.0
Vista de pagina 0
1 2 3 4 5 6 ... 16 17

Indice de contenidos

Pagina 1 - Model 700

Model 700 Remote Sensor/Alarm Relay Module Operator’s Installation and Instruction Manual DETCON, Inc. 3200 Research Forest

Pagina 2

700 RAM I.M. AutoZero – used to perform AutoZero remotely AutoSpan – used to perform AutoSpan remotely, user is required to apply sp

Pagina 3 - Table of Figures

700 RAM I.M. 3. Set-up and Normal Operation In normal operation, the RAM display continuously shows the current sensor reading, whic

Pagina 4

700 RAM I.M. 3.2 Set AutoSpan Level Set AutoSpan Level is used to set the span gas concentration level that is being used to calibra

Pagina 5 - 1. Introduction

700 RAM I.M. scale range of the 700 Gas Sensor. The current relay configurational settings can be viewed in View Sensor Status menu

Pagina 6 - Figure 2 RAM Mounting

700 RAM I.M. 3.5 Signal Output Check Signal Output Check provides a simulated 4-20mA output and RS-485 Modbus™ output. The simula

Pagina 7 - 1.3 Field Wiring

700 RAM I.M. 5. RAM Electronics Warranty Detcon Inc. warrants, under intended normal use, each new Model 700 RAM module to be free

Pagina 8

700 RAM I.M. 6.1 Spare Parts Part Number Spare Parts 500-005136-100 RAM Display PCA 500-005135-100 RAM Connector Board 500-0051

Pagina 9 - 2. Operator Interface

700 RAM I.M. 6.2 Revision Log Revision Date Changes made Approval1.0 03/16/2011 Made changes to reflect new RAM assembly. LU

Pagina 10 - 700 RAM I.M

700 RAM I.M. 700 RAM I.M. ii This page left intentionally blank Shipping Address: 3200 A

Pagina 11 - 3.1 View Sensor Status

700 RAM I.M. 700 RAM I.M. iii Table of Contents 1. Introduction ...

Pagina 12 - 3.3 Set Serial ID

700 RAM I.M. 700 RAM I.M. iv This page left intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The

Pagina 13

700 RAM I.M. 1. Introduction 1.1 Description The Model 700 Remote Sensor/Alarm Relay Module (known as the Remote Alarm Module or

Pagina 14 - Protocol

700 RAM I.M. 5.5"5.2"5.825"Ø0.2750 x2MountingBoltWall (or othermounting surface)4.35"Three - ¾" NPT Fittings

Pagina 15 - 6. Specifications

700 RAM I.M. junction box via two machine screws allowing the RAM display and RAM connector board to unseat from the 12-pin plug-in

Pagina 16 - 6.1 Spare Parts

700 RAM I.M. necessary to install/use the Transient Protection Module shipped with the 700 sensor. The 700 sensor may arrive from th

Pagina 17 - 6.2 Revision Log

700 RAM I.M. NOTE: Both the 3-wire power/mA cable and the 2-wire Modbus™ serial communications cable are required when remote wiri

Comentarios a estos manuales

Sin comentarios